Equipment approved on its first acceptance test.

Design, fabrication, automation and rebuilds for plants that cannot stop. For confidentiality, we do not publish the client's name in each case.

Tier 1 automotive · Automation and safety retrofit

Band saw automated with servo, PLC and safety guarding

The challenge

The operator worked too close to the moving blade, and test tires could be ejected during the cut. The goal was to remove the operator from the danger zone and increase cutting capacity without compromising the machine's original structure.

The solution

  • Table extended by 500 mm and rebuilt in aluminum, with manual 0–15° tilt for angled cuts.
  • Perimeter guard with an interlocked door that isolates the blade.
  • Servo with ball screw to drive the table, a VFD for the blade motor and a gear reducer to unload the servomotor.
  • Siemens HMI with S7-1200 PLC: feed, blade speed, automatic mode, cut counter, statistics, alarms and emergency stops.
≈40%Cycle per part from 10 to 6 min
ZeroOperator exposure during the cut
+500 mmOf aluminum table

SolidWorks · EPLAN · TIA Portal · S7-1200 · Servo + VFD

Multinational tire maker · Exported to Canada

Two final tire inspection stations

The challenge

Give the operator an ergonomic station for the final quality inspection of the finished tire.

The solution

  • An Atlas Copco air motor drives a roller and a NEXEN clutch moves the rotating platform.
  • Multilift lifting columns adjust the height of the whole system.
  • A PHD guided cylinder brings the tire toward the operator and another adjusts the roller tilt.
  • Allen-Bradley sensors provide feedback to the control system.

The result

Functional test at our shop with the client's engineer present and remote validation from Canada. Both machines passed on the first test and shipped crated, with nameplates in technical English.

2Stations built and tested
100%Approved on their first functional test
CanadaExport destination

SolidWorks · Allen-Bradley · Pneumatics · Progress reports to the client

Multinational tire maker · Fabrication and automation · 5 units

Automated foam presses

The challenge

The client had an obsolete foam press and needed to modernize and automate it.

The solution

  • Fabrication of the structure, guarding and mechanical components at our plant.
  • Pneumatic and control integration with a Siemens S7-1200 PLC.
  • Safety system with light curtains, operator station and emergency stop.
  • Commissioning and functional testing at our plant before every shipment.

The result

5 presses delivered: 4 to the client's plants in Mexico's Bajío region and 1 exported to the United States. All were approved on their first acceptance test.

5Presses delivered
4In Bajío region plants
1Exported to the U.S.

TIA Portal · S7-1200 · Safety light curtains · Pneumatics

Rebuilds, fabrication and machining

Tap any photo to view it larger.

Building machine after the rebuild Building machine before the rebuild BeforeAfter

Multinational tire maker · Rebuild

Building machine rebuild

Complete teardown, mechanical repair, rewiring and paint. The machine went back into production. Drag the handle to compare.

Tire handling machine with lift table, foot pedal and pull-cord emergency stop, inside a mesh-guarded cell

Design and fabrication · Machine safety

Tire handling machine in a guarded cell

Lift table, foot pedal, control panel, pull-cord emergency stop and a mesh cell with access door.

Bead machine before the rebuildBefore
Bead machine after the rebuildAfter

Multinational tire maker · Rebuild

Bead machine rebuild

Complete mechanical, electrical and paint rebuild of the equipment.

Heavy process machine component lifted with a forklift and chains
Large-diameter gear removed for repair

Major maintenance · On site

Major overhaul of process machinery

Removal, rigging and repair of heavy components: frames, shafts and large-diameter gears.

Machined housings and parts on a rack at VICA's shop
Aluminum machined parts on a shop table

Machining

Machined aluminum parts

Housings and components machined in our shop.

Roller conveyor being assembled at VICA's shop

Multinational tire maker · Export

Roller conveyors for North America

Conveyor assemblies built, tested and crated at our shop for a plant in North America.

Control panel with drives, PLC and contactors during decommissioning

Plant closure · Decommissioning

Decommissioning of tire building lines

De-energizing, removal and separation of components from first- and second-stage machines, with a crew of about 10 people.

Finished tilting conveyor

Design and fabrication

Tilting conveyor

Belt conveyor with a tilting frame, designed and built in our shop.

Machined stainless steel barrel and end caps

Curing press · Machining

Double-acting stainless steel cylinder

Actuator for the bladder of a steam-operated press. Barrel and end caps machined and honed in stainless steel.

Have a similar project?

Send us photos or drawings on WhatsApp and we will reply within 24 hours.

WhatsApp 442 114 1646
WhatsApp Call